Construction Red Emulsion Wall Paint For Outdoor Decorative Wall Surface

Construction Red Emulsion Wall Paint For Outdoor Decorative Wall Surface

Product features
1. Super performance: in the severe weather conditions, shows excellent weathering resistance and color retention, it has performance advantages, acknowledged widely by the domestic and foreign real estate developers.
2. Excellent antibacterial factor that fight alga, paint film ensures that the high quality for ten years.
3. Super waterproof function: special micro-porous structure, it can prevent moisture penetration and make its excess moisture release, was praised as a European architecture breathing film.
4. Strong adhesion performance and resistance to alkali : use atomic separation technology, automatic deep in wall paint film, never fall off, for can lead to saponification, uneven discoloration with excellent resistance.
5. Strong self-cleaning performance: take the lead in the high-tech nano materials technology, carefully developed and manufacture, the paint film will be clean automatically along with the rain washing, maintain the luster of metope.

Scope of application
It is used for outdoor decorative wall surface.

Product parameters
Type: Import water-based fluorocarbon resin.
Sheen: shiny
Methods: brushing, rolling and spraying
Paint consumption: 13-18 square meters/liter/ layer
Dilution: diluted with water, the maximum of water addition is 20% (mass ratio)
Recoat time: 2 h (25 ℃)
surface dry: about 30 min
Quality standard: in accordance with the national standard GB/T9755-2001
Suggested use:1 primer and 2 finish
Storage: use cap sealed tightly, stored in (more than 0 ℃, 35 ℃ below) a cool, dry place.
Cleaning tools: with clean water.
Packing specification: 18 L / 5 L/barrel.

Construction technology
1. The base surface must be clean, dry, firm and no dust. New cement metope to maintain at least for a month, more than 7 weeks in winter. Washing dust and bacterium from old wall with high pressure, cleaning and airing, ensure that no oil and without mildew algae and other attached objects. The mold wall use sand paper to grind, so that remove the mould, it is necessary to brush again washing mold water , and then clean again with clean water,  paint again after dry.
2. The construction temperature > 5 ℃, humidity < 85%, PH < 10, wall's humidity < 6%, putty is fully dry, it can construction when meet  above conditions.
3. Please do not construction at the same time with polyester paint, should construction polyester paint after the emulsion paint dry.
4. Before construction should stir well, and the construction according to the requirements.
5. Protection: more than seven days.
 

The coating process
1. Clean up the scene, cover the ground and the furniture with matting, and use the sealing tape to separate different color area;
2. Inspect construction wall condition and in accordance with the requirements of construction to add water to dilute. There are too much water will effect and quality and gloss of the paint,  if there are too little water, it will affect brushing;
3. Brush: should be from top to bottom, vertical direction and then horizontal direction, brush evenly,  finally comb brush marks gently in vertical direction. if the operation is not skilled, the coating will produce brush marks, sagging, uneven coating defects.
4. Roller coating: brush in "Z" type first, and then, roll in vertical direction one time in turns, at last available wool brush combing roller brush marks in vertical direction, choose proper roller, brush touch paint evenly.
5. Cleaning: clean all tools with clean water immediately, to prevent the brush roller hardening.

Coating techniques: if you use the same color different batch of paint brush on the same plane, and they should be mixed in a larger container before using, in order to make sure the color uniformity of the whole.

Attention
Health, environmental protection, application instructions:
1. Do not swallow, if liquid paint splashed into eye accidentally, clean with water immediately;
2. Paint liquid waste disposal, it shall comply with the environmental protection standard;
3. The product performance and application of listed above data are obtained under experimental conditions, please according to our company's instructions.
 

FOR DELIVERY: